# Ink Storing Box with Ink Leak Detection Sensor (RIPS)

1. Release the 6 locks (A), and remove the 6 Ink Pack Trays (B). (Only perform for SC-P8500DL series/SC-T7700DL series)
   

2. Open the Maintenance Cover (A). (Only perform for SC-P8500DL series/SC-T7700DL series)

   

3. Remove the screw. (Only perform for SC-P8500DL series/SC-T7700DL series)
   
   
   • :Black M3x8 S-tite screw

4. Release the hook, and remove the Ink Holder (RIPS) Upper Cover (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   Assembly / 組み立て

   Insert the Ink Holder (RIPS) Upper Cover (A) tab (B). Insert the Ink Holder (RIPS) Upper Cover (A) hook (C).

5. Remove the two screws, and remove the USB cable (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   • : Silver M3x8 P-tite screw

6. Remove the two screws. (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   • : Silver M3x8 S-tite screw
7. Pull the Ink Pack Tray Right Side (A) slightly forward and release the 2 dowels. (Only perform for SC-P8500DL series/SC-T7700DL series)

8. Slide the Ink Pack Tray Right Side (A) upwards to remove. (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   Assembly / 組み立て

   The gray lock lever (A) and ink plate (B) will come off when removing the Ink Pack Tray Right Side (C). Install them after installing the Ink Pack Tray Right Side (C) in the main unit. With the lock lever (A) and tray lever (B) moved to the right side, install the Ink Pack Tray Right Side (C). After installing the Ink Pack Tray Right Side (A), move the lock lever (B) and confirm that the tray lever (C) moves in conjunction.

9. Open the Maintenance Box Cover (A).
   
10. Release the 2 tabs of the Maintenance Box Cover (A) in the order shown in the figure below, and remove.
    
11. Remove the Maintenance Box (A).
    
12. Remove the screw.
    
    
    • : Silver M3x8 Cup S-tite screw
13. Insert a flathead screwdriver and release the 2 hooks each, and remove the two screw cover (A).
    
14. Insert a flathead screwdriver and release the 2 hooks, and remove the screw cover (A).
    
15. Remove the three screws at the front side.
    
    • : Black M3x8 Cup P-tite screw
16. Remove the five screws at the right side.
    
    • : Silver M3x8 Cup S-tite screw
    • : Silver M4x8 Cup S-tite screw
17. Remove the four screws at the rear side.
    
    • : Silver M3x8 Cup S-tite screw with plastic washer
    • : Silver M3x8 Cup S-tite screw
18. On the printer rear side, release the dowel of the Home Side Cover Unit (A).
    
19. Insert a flathead screwdriver and release the 2 tabs each, and remove the Home Side Cover Unit (A) in the direction of the arrow.
    
20. Open the IH Cover Unit (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
    
21. Slide the Ink Pack Tray Left Side (A) upwards and release the 3 hooks to remove. (Only perform for SC-P8500DL series/SC-T7700DL series)
    
22. Open the Ink Cartridge Cover (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
23. Remove the two screws.
24. Release the 2 hooks and then remove the Take-up Button Board Cover (A).
    
    • : Black M3x10 Cup P-tite screw (SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series only)
    • : Black M3x10 Cup P-tite screw (SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    • :Black M3x6 Cup S-tite screw (SC-P8500DL series/SC-T7700DL series)
25. Remove the cable (A) from the connector.
    
26. Open the Ink Cartridge Cover (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
27. Remove the two screws.
28. Release the 2 hooks and then remove the Roll Removal Board Cover (A).
    
    • : Black M3x10 Cup P-tite screw (SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    • :Black M3x6 Cup S-tite screw (SC-P8500DL series/SC-T7700DL series)
29. Remove the cable (A) from the connector.
    

30. Remove the two screws, and remove the Maintenance Cover (A).
    
    
    

    • : Silver M3x8 Cup S-tite screw
31. Remove the cable (B) from the relay connector (A).
32. Release the cable (B) from three clamps.
    
    

    Assemble / 組み立て

    Push the two dowels (A) of the Maintenance Cover (A) in the positioning holes of the case.

33. Open the IH Cover Unit (A).
34. Release the Storage Housing (B) tab, and fully open the IH Cover Unit (A).
    
35. Remove the IH Cover Unit (A) upward.
    
36. Remove the two screws.
    
    
    • : Black M3x8 Cup S-tite screw
37. On the rear of the printer, raise the Storage Housing (A) slightly, and release the Storage Housing (A) tab.
    
38. Remove the Storage Housing (A) frontward.
    

39. On the printer front side, remove the three screws.
    

    • : Black M3x8 Cup S-tite screw
40. Remove the 3 screws on the printer rear side.
    
    

    • : Black M3x8 Cup S-tite screw

41. Remove the CSIC FFC (A).
    

42. Pull the Ink Holder (RIPS) (A) forward slightly, and remove the cable (B) from the connector.
    

    Caution / 注意

    Ink may drop from the Ink Holder (RIPS) joint (A). Therefore, keep rags handy in advance to prevent the surroundings from getting soiled.

43. Remove the Ink Holder (RIPS) (A) frontward.

    
    

    
    

    Assembly / 組み立て

    Install the Ink Holder (RIPS) (A) tab (B) along the main unit rail (C). When replacing the Ink Holder (RIPS) (A), to prevent ink leakage, tie the tube (B) of the replaced Ink Holder (RIPS) (A) tightly as shown in the figure below for transportation. Insert the tube firmly up to the base of the joint.

44. Remove the cable (A) from the relay connector.
    

45. Remove the screw.
    

    • : Silver M3x8 Cup S-tite screw

46. Slide the Ink Storing Box with Ink Leak Detection Sensor (A) in the direction of the arrow to remove.