# Paper Eject Driven Roller Unit

1. Release the 6 locks (A), and remove the 6 Ink Pack Trays (B). (Only perform for SC-P8500DL series/SC-T7700DL series)
   

2. Open the Maintenance Cover (A). (Only perform for SC-P8500DL series/SC-T7700DL series)

   

3. Remove the screw. (Only perform for SC-P8500DL series/SC-T7700DL series)
   
   
   • :Black M3x8 S-tite screw

4. Release the hook, and remove the Ink Holder (RIPS) Upper Cover (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   Assembly / 組み立て

   Insert the Ink Holder (RIPS) Upper Cover (A) tab (B). Insert the Ink Holder (RIPS) Upper Cover (A) hook (C).

5. Remove the two screws, and remove the USB cable (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   • : Silver M3x8 P-tite screw

6. Remove the two screws. (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   • : Silver M3x8 S-tite screw
7. Pull the Ink Pack Tray Right Side (A) slightly forward and release the 2 dowels. (Only perform for SC-P8500DL series/SC-T7700DL series)

8. Slide the Ink Pack Tray Right Side (A) upwards to remove. (Only perform for SC-P8500DL series/SC-T7700DL series)
   

   Assembly / 組み立て

   The gray lock lever (A) and ink plate (B) will come off when removing the Ink Pack Tray Right Side (C). Install them after installing the Ink Pack Tray Right Side (C) in the main unit. With the lock lever (A) and tray lever (B) moved to the right side, install the Ink Pack Tray Right Side (C). After installing the Ink Pack Tray Right Side (A), move the lock lever (B) and confirm that the tray lever (C) moves in conjunction.

9. Open the Maintenance Box Cover (A).
   
10. Release the 2 tabs of the Maintenance Box Cover (A) in the order shown in the figure below, and remove.
    
11. Remove the Maintenance Box (A).
    
12. Remove the screw.
    
    
    • : Silver M3x8 Cup S-tite screw
13. Insert a flathead screwdriver and release the 2 hooks each, and remove the two screw cover (A).
    
14. Insert a flathead screwdriver and release the 2 hooks, and remove the screw cover (A).
    
15. Remove the three screws at the front side.
    
    • : Black M3x8 Cup P-tite screw
16. Remove the five screws at the right side.
    
    • : Silver M3x8 Cup S-tite screw
    • : Silver M4x8 Cup S-tite screw
17. Remove the four screws at the rear side.
    
    • : Silver M3x8 Cup S-tite screw with plastic washer
    • : Silver M3x8 Cup S-tite screw
18. On the printer rear side, release the dowel of the Home Side Cover Unit (A).
    
19. Insert a flathead screwdriver and release the 2 tabs each, and remove the Home Side Cover Unit (A) in the direction of the arrow.
    
20. Insert a flathead screwdriver and release the two hooks, and remove the screw cover (A).
    
21. Open the Printer Cover (A) and the Cutter Cover (B).
    
22. Remove the three screws at the front side.
    
    • : Silver M3x10 Cup P-tite screw
    • : Silver M3x8 Cup S-tite screw
23. Remove the screw at the top side.
    
    • : Silver M3x8 Cup S-tite screw
24. Remove the four screws at the rear side.
    
    • : Silver M3x8 Cup S-tite screw with plastic washer
    • : Silver M3x8 Cup S-tite screw
      
25. Remove the four screws at the left side.
    
    • : Silver M3x8 Cup S-tite screw

26. On the printer rear side, release the dowel of the Full Side Cover Unit (A).
    

27. Remove the Full Side Cover Unit (A) from the dowels, and remove it while it in the direction of the arrow.
    

    Assemble / 組み立て

    When installing the Full Side Cover Unit (B), carefully the Head FFC (A) so that it does not damage.

28. Release the sensor cable (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DL series/SC-T7700DL series)
    
29. Open the Printer Cover (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DL series/SC-T7700DL series)

30. Remove the Home Side Top Cover (B). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DL series/SC-T7700DL series)
    

31. Remove the four screws at the front side. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DL series/SC-T7700DL series)
    

    • (Right):Silver M3x8 Cup S-tite screw

    • (Left):SC-P8500D series/SC-T7700D series/SC-P8500DL series/SC-T7700DL series: Silver M3x8 Cup S-tite screw, SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series: Silver M4x6 Shoulder Screw
    • : Silver M3x10 Cup P-tite screw

    Assemble / 組み立て

    Tighten the right green screw with the grounding cable. (SC-P8500D series/SC-T7700D series/SC-P8500DL series/SC-T7700DL series only)

32. Remove the screws on the top. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DL series/SC-T7700DL series)
    SC-P8500D series/SC-T7700D series/SC-P8500DL series/SC-T7700DL series: 6 pcs
    
    
    • : Black M3x8 Cup S-tite screw
    SC-T5700D series: 4 pcs
    
    
    • : Black M3x8 Cup S-tite screw
    SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E: 2 pcs
    
    • : Black M3x8 Cup S-tite screw
33. Remove the Front Top Cover (A) frontward. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DL series/SC-T7700DL series)
    
34. Open the IH Cover Unit (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
    
35. Slide the Ink Pack Tray Left Side (A) upwards and release the 3 hooks to remove. (Only perform for SC-P8500DL series/SC-T7700DL series)
    
36. Remove the Button (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
37. Remove the two screws, and then remove the Scanner Home Side Cover (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • : Silver M3x8 Cup P-tite screw
38. Push two buttons (A), and open the Scanner Unit (B). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
39. Remove the screw on the printer home side. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
40. Remove the C Shape Washer (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • : Black M3x4 Cup Step type S-tite screw
41. Remove the Fixing Slider (A) from shaft. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
42. Remove the screw on the printer full side. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
43. Remove the C Shape Washer (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • : Black M3x4 Cup Step type S-tite screw
44. Remove the Fixing Slider (A) from shaft. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
45. Open the Scanner Unit (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
46. Release the sensor cable (A). (Only perform for SC-P8500DL series/SC-T7700DL series)
47. Remove the two screws. (Only perform for SC-P8500DL series/SC-T7700DL series)
    
    
    • : Silver M3x8 Cup S-tite screw
48. Remove the screw, and then remove the Scanner Full Side Front Cover (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • : Silver M3x8 Cup S-tite screw

    Check Point / チェックポイント

    Scanner Full Side Front Cover of SC-T5700DM series

49. Remove the C Shape Washer (A) and the Fixing Slider (B). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
50. Remove the Washer (A) and the Strap (B). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
51. Remove the four screws. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • :Silver M3x8 P-tite screw with built-in washer
52. Hang each of the two fixing sliders (A) on the shaft. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    

53. Release the 10 hooks and remove the Scanner Front Cover (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    

    Assembly / 組み立て

    Install the Scanner Front Cover (A) while engaging its 10 hooks (B) and 13 tabs (C) with the positioning points on the scanner.

54. Remove the three screws, and then remove the Scanner Front Top Cover (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • : Silver M3x6 Cup S-tite screw

    Assembly / 組み立て

    Install the Scanner Front Top Cover (A) while inserting its three dowels into the positioning holes in the scanner.

55. Remove the eight screws and then remove the Printer Top Cover (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    • : Silver M3x8 Cup P-tite screw
    • : Silver M3x8 Cup S-tite screw
    • : Black M3x8 Cup S-tite screw
56. Release cable (B) from clamp (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)

57. Release the cable on the Cable Routing Holder (C), and remove the Cable Routing Holder (C). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    

    Assembly / 組み立て

    Attach the Cable Routing Holder (B) to the shaft (A) of the Scanner Unit. Attach the tab (C) of the Scanner Unit to the Cable Routing Holder (B).

58. Release the cable from two clamps (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
59. Remove the two cables (C) from the connectors (B) of the Scanner Main Board. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
60. Remove the two cables (B) from wire saddle (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
61. Remove the four screws. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    
    
    • : Silver M4x10 Cup S-tite screw
62. Attach the fixed slider on each of the two shafts. (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
63. Release the sensor cable (A). (Only perform for SC-T5700DM series)
    
64. Close the Scanner Unit (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)

65. Remove the Scanner Unit (A). (Only perform for SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    

    Assembly / 組み立て

    Install the Scanner Unit while engaging its positioning holes with the two protrusions (A) on the printer.

66. Open the Ink Cartridge Cover (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
67. Remove the two screws.
68. Release the 2 hooks and then remove the Take-up Button Board Cover (A).
    
    • : Black M3x10 Cup P-tite screw (SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series only)
    • : Black M3x10 Cup P-tite screw (SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    • :Black M3x6 Cup S-tite screw (SC-P8500DL series/SC-T7700DL series)
69. Remove the cable (A) from the connector.
    
70. Open the Ink Cartridge Cover (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
71. Remove the two screws.
72. Release the 2 hooks and then remove the Roll Removal Board Cover (A).
    
    • : Black M3x10 Cup P-tite screw (SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    • :Black M3x6 Cup S-tite screw (SC-P8500DL series/SC-T7700DL series)
73. Remove the cable (A) from the connector.
    

74. Remove the two screws, and remove the Maintenance Cover (A).
    
    
    

    • : Silver M3x8 Cup S-tite screw
75. Remove the cable (B) from the relay connector (A).
76. Release the cable (B) from three clamps.
    
    

    Assemble / 組み立て

    Push the two dowels (A) of the Maintenance Cover (A) in the positioning holes of the case.

77. Detach the Ink Ink Cartridge Cover (A) from the three shafts. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
78. Remove the six screws. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)
    
    • : Silver M3x8 Cup S-tite screw
      
      

79. Release the dowel of the Ink Holder Housing (A), and remove it frontward. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series/SC-P8500DM series/SC-T7700DM series/SC-T5700DM series)

    

    Caution / 注意

    Carefully remove the Ink Holder Housing not to pull the cables connected to the cover.

    Assemble / 組み立て

    When removing the Ink Holder Housing (C) to remove another part or component, remove the sensor (B) from the relay connector (A), and then place the cover beside the printer. If the ink tube (A) is detached from the hook of the Ink Bifurcated Flow Channel Unit (B), set the tube properly, or ink may not be supplied to the ink tube, resulting in print failure.

80. Remove the two screws , and remove the USB cable (A). (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series)

81. Disengage the sensor (B) from the two hooks. (Only perform for SC-P8500D series/SC-T7700D series/SC-T5700D series/SC-P6500D series/SC-P6500DE series/SC-T3700D series/SC-T3700DE series/SC-P6500E series/SC-T3700E series)
    
    • : Silver M3x8 P-tite screw
82. Open the Front Cover (A). (Only perform for SC-P6550E series/SC-T3750E series)
    
83. Release the dowels of the Front Cover (A) in the order shown in the figure below, and remove. (Only perform for SC-P6550E series/SC-T3750E series)
    
84. Remove the four screw, and remove the Rear Cover (A). (Only perform for SC-P6550E series/SC-T3750E series)
    
    
    • : Black M3x8 Cup S-tite screw with plastic washer
    • : Black M3x8 Cup S-tite screw
85. Remove the 2 screws and remove the Left Cover (A) in the direction of the arrow. (Only perform for SC-P6550E series/SC-T3750E series)
    
    
    • : Black M3x8 Cup S-tite screw
      
      
86. Remove the 2 screws and remove the Right Cover (A). (Only perform for SC-P6550E series/SC-T3750E series)
    
    
    • : Black M3x8 Cup S-tite screw
87. Pull out the Lower Spindle Holder (A).
88. Pull out the Inner Home Side Lower Cover (B) to the front to remove.
    
    • : Silver M3x8 Cup S-tite screw
89. Remove the screw.
    
    • : Silver M3x8 Cup S-tite screw
90. Raise the paper guide (A), and remove the screw.
    
    • : Silver M3x8 Cup S-tite screw
91. Pull out the Paper Basket Unit (A).
92. Pull out the Inner Home Side Upper Cover (B) to the front to remove.
    
93. Pull out the Lower Spindle Holder (A).
94. Remove the 5 screws.
    
    • : Silver M3x8 Cup S-tite screw
95. Raise the paper support (A), and remove the screw.
    
    • : Silver M3x8 Cup S-tite screw
96. Pull out the Inner Full Side Cover (A) to the front to remove.
    
97. Remove the screw.
    
    • : Silver M4x6 Cup S-tite screw
98. Disengage the Production Stacker Paper Jam Detection Sensor (B) from the shaft (A).
    
99. Release cable (B) from the hook (A).

100. Disconnect the cable (B) from the connector (C) on the backside.
     

     Assemble / 組み立て

     There are positioning locations.

1. Remove the two screws.
2. Release the two ink tubes (B/C) from the two guides of the Head Maintenance Cover Front (A).

3. Release the three ink tubes (B/C/D) from the guide of the Head Maintenance Cover Front (A), and remove it.
   

   • : Silver M3x10 Cup P-tite screw

   
   

   Assembly / 組み立て

   Be careful not to pinch the ink tube with the front of the head maintenance cover. There are two types of Head Maintenance Cover Front, and the assembly method differs depending on the shape. For shape A Route the ink tubes (A) of the Ink Bifurcated Flow Channel Unit through the guides. Put the marking portions (B/C/D) of the ink tubes in the guides. Align the marking of the ink tube (E) with top edge of the hook of the Ink Bifurcated Flow Channel Unit. For shape B Route the ink tubes of the Ink Bifurcated Flow Channel Unit through the guides. Place the ink tube (A) in the upper guide and the ink tube (B/C) in the lower guide. Align the marking of the ink tube with top edge of the hook of the Ink Bifurcated Flow Channel Unit. Make sure that the Ink Tube (B) is not crushed when the Ink Holder Housing (A) is installed. Insert the Ink Tube (C) and Ink Tube (D) parallel to each other into the slit in the Head Maintenance Cover Front (E).

101. Remove the two screws.
102. Release the two ink tubes (B/C) from the two guides of the Head Maintenance Cover Front (A).

103. Release the three ink tubes (B/C/D) from the guide of the Head Maintenance Cover Front (A), and remove it.
     

     • : Silver M3x10 Cup P-tite screw

     
     

     Assembly / 組み立て

     Be careful not to pinch the ink tube with the front of the head maintenance cover. There are two types of Head Maintenance Cover Front, and the assembly method differs depending on the shape. For shape A Route the ink tubes (A) of the Ink Bifurcated Flow Channel Unit through the guides. Put the marking portions (B/C/D) of the ink tubes in the guides. Align the marking of the ink tube (E) with top edge of the hook of the Ink Bifurcated Flow Channel Unit. For shape B Route the ink tubes of the Ink Bifurcated Flow Channel Unit through the guides. Place the ink tube (A) in the upper guide and the ink tube (B/C) in the lower guide. Align the marking of the ink tube with top edge of the hook of the Ink Bifurcated Flow Channel Unit. Make sure that the Ink Tube (B) is not crushed when the Ink Holder Housing (A) is installed. Insert the Ink Tube (C) and Ink Tube (D) parallel to each other into the slit in the Head Maintenance Cover Front (E).

104. Remove the four screws, then remove the Cutter Maintenance Cover (A).
     
     • : Silver M3x8 Cup S-tite screw
105. Remove the screw and then remove the Paper Eject Release Roller Belt Cover (A).
     
     • : Silver M3x8 Cup S-tite screw

106. Turn the Paper Eject Release Roller (A) until the flag (B) is lowered so that the flag does not contact with the encoder (C).
     
     
     

107. Remove the three screws, then remove the Paper Eject Star Wheel Roller Motor Unit (A).

     

     • : Silver M3x8 Cup S-tite screw

     Caution / 注意

     Take care not to drop the two gears (A). When attaching the gears, if the gears are attached in the opposite direction, the Paper Eject Star Wheel Roller Motor Unit cannot be installed in the correct position, and a motor error such as " 00128A (Paper Eject Driven Roller Motor Overload Error)" may occur.

108. Use a flathead screwdriver to release the two hooks, then remove the Motor Cover (A).
     

109. Remove the cable from the two connectors (A), and remove the Paper Eject Star Wheel Roller Motor Unit (B).
     

     Assemble / 組み立て

     Level out the direction of the holes of the two shafts (A) of the Paper Eject Star Wheel Roller Unit. Check that the Jagged Roller (C) of the EJ Wheel (B) in front and behind is facing downward.

110. Remove the three screws that secure the Paper Eject Driven Roller Unit.
     
     • : Silver M3x8 Cup S-tite screw
111. Remove the screw that secures the EJ Wheel Holder 1 (A).
     
     • : Silver M3x8 Cup P-tite screw
112. Slide the EJ Wheel Holder 1 to disengage the two hooks and remove it.
     
113. Remove the screw that secures the EJ Wheel Holder 2 (A).
     
     
     • : Silver M3x8 Cup P-tite screw
114. Slide the EJ Wheel Holder 2 to disengage the two hooks and remove it.
     
115. Remove the screw that secures the EJ Wheel Holder 3 (A).
     
     
     • : Silver M3x8 Cup P-tite screw
116. Slide the EJ Wheel Holder 3 to disengage the two hooks and remove it.
     

117. Remove the screw.
     

     • : Silver M3x8 Cup P-tite screw
118. Slide the EJ Wheel Holder 4 to disengage the three hooks and remove it toward you.
     
119. Remove the torsion spring (A) at the full side.
     
120. Remove the two torsion springs (A) at the Home side.
     
121. Remove the two plastic washers (A).
122. Remove the two gears (B).
     
123. Disengage the dowels and remove the two bushing (A).
     
124. Remove the plastic washer (A) at the full side.
125. Disengage the dowel and remove the bushing (B).
     
126. Remove the plastic washer (A).
127. Disengage the dowel and slide the bushing (B) toward the inside.
     
128. Slide the EJ Lock Lever upward. Pull out the three tabs from the frame and remove it.
     
129. Slide the shaft holder (A) in the direction of the arrow at the full side.
     
130. Pull out the two shafts (A) of the Paper Eject Star Wheel Roller Unit from the two shaft holes of the frame at the full side.
     
131. Pull out the two shafts (A) of the Paper Eject Star Wheel Roller Unit from the frame at the home side.
     

132. Remove the Paper Eject Star Wheel Roller Unit (A).
     

     Assemble / 組み立て

     Before installing the Paper Eject Star Wheel Roller Unit, check to make sure that all the Wheel Rollers (A) are installed. If the Wheel Rollers (A) are detached, push them in the Paper Eject Star Wheel Roller Unit forward from the shaft with the protrusion (B) to install them. Level out the direction of the holes of the two shafts (A) of the Paper Eject Star Wheel Roller Unit. Check that the Jagged Roller (C) of the EJ Wheel (B) in front and behind is facing downward.

     Lubrication / 注油

     Before attaching the part, refer to the following and then lubricate. Lubrication 4 Lubrication 6