| No. | Operation details | Errors that may occur during execution |
|---|
| 1 | Recieve the printing data. | --- |
| Start to print. |
2
| Judge the possible to print or not.
| (1) | BPE: Check if there is paper by confirming whether there is roll paper (UPE: board / cut sheets)
| No paper error
Paper size / type / width / length is different: mismatch error
- Paper Type Error
- Paper Size Error
- Paper Length Error
- Paper Width Error
Dual Roll: Auto select roll paper -> Roll paper swtich error
paper path error: paper path is different -> Although it is a roll paper, it is the data of a single sheet paper (and vice versa / board paper) |
| (2) | Judge whether borderless printing is possible. | Borderless printing impossible error (Absorbent is full / Paper width is borderless Printing is not possible: Physically incompatible media Not used: Paper width is judged. It should already be included) |
| (3) | Perform a paper support position check. | Lock lever print impossible error (normal error when the position is different) |
| (4) | Check whether quick cut mode. | --- |
| 3 | Enable print paper feeding. | (1) | Stabilization the paper on the platen. | Close the suction chamber switching division plate. | |
| Check and set the suction fan and operate. | |
| (2) | Paper feed driven release (side that is active) | 1st paper feed driven release or 2nd paper feed driven release driving (side that is active) | |
| (3) | Determine whether paper is loaded in reel (when take-up reel setting: 2nd paper feed / 1st take-up) | Memorize the PF position when start sequence. | --- |
| Feed the paper. | |
| Repeat the reel measurement sequence four times. | |
| Perform PE sensor real-time paper detection. | 920500 (Cover open error (normal error) ) |
| (4)
| Prepare to starting print.
| Renew the paper front edge information.
Cut the paper if a barcode remains. | |
Set the borderless margine number for printer the top and bottom of paper.
Refresh the margins: Perform cutting. | |
Unlock the CR: only when borderless printing | |
| Change the PG for print: only when borderless printing | |
| Feed the paper: only when borderless printing | |
Adjust the PW sensor sensitivity: Only when borderless printing (To adjust the sensitivity for borderless printing. The sensitivity is adjusted because printing of 1st sheet. It is not necessary from the 2nd sheet.) | |
| (5) | Prepare the function to use. | Move the CR. (In case of CR is not been home position, do the 'home seek' operation.) | |
| Nip the eject roller dur to media setting. | |
4
| Adjust the mech unit by automatically.
| (1) | Adjust the CR controll. | Calibrate the CR active dumper. | |
| Unlock the CR. | |
| Change the paper gap to ""++"". | |
| Flush before printing. | |
| Judge the active dumper calibration. | |
| Close the print head cap. | |
| 5 | Activate the safety function to print. | (1) | Turn on the in-printer LED (does not light / too bright). | --- |
| 6 | Prepare the nozzle. | (1) | Do the maintenance before printing. | |
| 7 | Prepare the paper to print. | (1) | Initializetion and auto paper feeding to start printing. | |
| 8 | Set the printing information. | --- |
| 9 | Prepare the CR to start print. | --- |
| Prepare the 1 pass printing. |
10 | Prepare the print head to print. | |
| 11 | Prepare the CR to print.
| |
| Printing. |
| 12 | Detect the paper edge from full to home side at printing home to full side. | |
| 13 | Detect paper edge home side at printing full to home side. | |
| Finish the 1 pass printing. |
| 14 | Calcurate the 1 pass printing counter. | |
| 15 | Prepare the next pass printing. Borderless printing is not possible when borderless printing (when maintenance box is full): Can proceed if not borderless printing. | |
| Paper fees the printing result. |
| 16 | Paper feed to next pass printing position.
| Paper end detect/with/without paper detection/paper feed related error |
| 17 | Prepare the next paper feeding. | |
| Repeat the No.10 to 17 until finishing 1 page printing. |
| Processing the finish 1 page printing. |
18
| Paper feed to last page edge. | |
19
| Eject the paper .
| (1) | Check the print data being next page or not. | --- |
| (2) | Prepare the paper ejection. | --- |
| (3) | Eject paper → cut
| |
| (4) | Check the paper posture after printing. | |
| (5) | If the Bulk Stacker is enabled, check whether it is full of printed media. | Stacker full error (Paper jam error)
-> Remove paer and press "OK" to return to the original → You can press OK, but if you do nothing while it is paper full, the same error will occur when printing the next page |
| 20 | Transition to idling if there is no next page. |
| Finish the priting. |
| 21 | Do the maintenance after printing.
| |
| 22 | Prepare finish printing.
| |
| 23 | Return the paper waiting position.
| |
| 24 | Judge the error. | (1) | Judge the part life end or not. | |
| 25 | Deactivate paper feeding. | |
| 26 | Cancel the CR printing ready state.
Disable the print safety function. | No error, just turn off the lights |
| 27 | Ready |
