| No. | Operation details | Errors that may occur during execution | Time |
|---|
| 1 | Set auto paper loading mode on. | --- | Approx. 5 sec. |
2
| Unlock the lock lever.
| ---
Screen for roll paper feeding guidance:
"The spindle lock lever is raised. Do you want to load roll paper? If you will not load roll paper, lower the spindle lock lever." " | Approx. 3 sec. |
| 3 | Install roll paper. | Spindle screen guidance: Set.
Not a normal error.
Spindle screen guidance: "The spindle lock lever is raised. Do you want to load roll paper? If you will not load roll paper, lower the spindle lock lever." does not disappear → Spindle detection is broken (sensor or a part for pressing is broken.)
| About 5 sec |
| 4 | Lock the lock lever.
| ---
Close the lock.
"The spindle lock lever is raised. Do you want to load roll paper? If you will not load roll paper, lower the spindle lock lever." | About 3 sec |
| 5 | Judge the position of the paper support lock lever and guide to the correct position. | - Lock lever position incorrect error
| Approx. 4 sec. |
| 6 | Move the paper support lock lever to the correct position. | ---
If it is in the correct position, transition to the paper selection screen. |
| 7 | Perform paper feeding from the panel. | ---
If you press OK, paper feeding starts.
OK: Proceed
Cancel: Idle | Approx. 7 sec. |
| Prepare the paper feed path. |
8
| Enable paper feeding.
| 1 | Withdraw the roll to the paper pack, (path opposite to path for paper feeding: 1st is selected, but return 2nd to paper pack) | | Approx. 25 sec. |
| 2 | Adjust interface of the roll edge sensor (1st Roll Paper Edge Detection Sensor or 2nd Roll Paper Edge Detection Sensor that is active) by loading paper: Adjust sensitivity. | |
| 3 | Set the paper edge sensor to ON (set 1st Roll Paper Edge Detection Sensor or 2nd Roll Paper Edge Detection Sensor that is active to ON). | |
| 4 | Drive the 1st roll (1st/2nd, side that is active) | The same error occurs for the 2nd roll. |
| 5 | Set the paper edge sensor to OFF (set 1st Roll Paper Edge Detection Sensor or 2nd Roll Paper Edge Detection Sensor that is active to OFF). | --- |
| 6 | 1st paper feed driven strong nip (1st/2nd, side that is active) | |
| 7 | Release the driven.
| |
| 8 | Nip the sub-driven.
| |
| 9 | Release the raised jag roller / EJ drive jag roller. | |
| 10 | Drive the 1st roll (1st/2nd, side that is active) | |
| 11 | Feed the paper to the sub-driven paper nip distance. | |
| 12 | 1st paper feed driven release (1st/2nd, side that is active, but motor is together) | |
| 13 | Enable tension control: Roll motor load measurement (1st/2nd, side that is active) | |
| 14 | Unlock the CR Unit | |
| 15 | Switch the PG.
<Position>:
Board paper: PG++
Other than board paper: PG+ | |
| 16 | Feed the paper from after the PE sensor to the nip pause position when feeding. | |
| 17 | Driven nip | |
| 18 | Open the suction chamber switching division plate (44-inch only: 36/24 do not have a shutter motor) | |
| 19 | Stabilize the paper on the platen. | Operate the suction fan. | |
9
| Set the paper posture.
| 1 | Enable paper coordination detection.
| Judge the paper thickness.
Look at PF nip sensor → If it is broken, a paper thickness error can be reset, but even if paper feeding is tried again, it will not be possible. | - paper thickness error (paper type, Paper path difference or foreign material)
| Approx. 49 sec. |
| 2 | Operate the suction fan. | |
3 | Switch the PG.
<Position>:
Board paper: PG++
Other than board paper: PG+
| Move the CR. | |
| 4 | Pass light through → detect the light shielding using APG Home sensor | |
| 5 | Judge the current PG and release the PG → switch to the target PG | |
| 6 | Feed the paper. | |
| 7 | Provisionally update the paper leading edge position. | --- |
| 8 | Feed the paper.
| |
| 9 | Move the CR (move it to the position at which sensitivity adjustment of the PW is possible). | |
| 10 | Adjust the PE sensor sensitivity.
Board paper / cut sheets: UPE Sensor
Roll paper: BPE Sensor | --- |
| 11 | Adjust the sensitivity of the PW sensor. | |
| 12 | Rewind the roll paper to take up the slack. | |
| 13
| Judge the paper posture (roll paper).
| Check for skewing based on the side edges.
| Detect the side position at the home side. | Move the CR.
Move to the side detection start position. | | Approx. 18 sec. |
14 | Move the CR.
Full-> Home |
| 15 | Sub driven release | |
16 | Feed the paper. | |
| 17 | Detect the side position at the home side. | Move the CR.
Move to the side detection start position. | |
18 | Move the CR.
Full-> Home |
| 19 | Calculate the skew amount. | Paper feed error when checking /paper skew error does not occured |
| 20 | Set the skew amount. | --- |
| 21 | Nip the sub-driven.
(Will not move if nipped. This operation is performed if the deskewing operation is performed)
| |
| 22 | Feed the paper. | |
| 23 | Update the real-time exterior shape measurement reference position. | --- |
10 | Measure the paper wide. | 1 | Detect the paper home side position. | |
| 2 | Detect the paper home side position. |
| 3 | Detect the pattern. | Feed the paper. | |
| Detect the pattern. | --- |
| 4 | Renew the paper front edge information. | --- |
| 5 | Update the reading result. | --- |
| 6 | Detect the paper full side position. | |
| 7 | Detect the top position at the full side. |
| 8 | Calcurate the front edge parallelism. | --- |
| 9 | Renew the paper front edge information.
Does not cut and no error (if, for example, the paper is skewed, printing is started aligned with the upstream side of the paper) | --- |
| 10 | Calculate the paper width. | --- |
| 11 | Set to the waiting state. | 1 | Move the CR to the standby position. | | Approx. 3 sec. |
| 2 | Feed the paper so that its leading edge comes to the paper feeding waiting position. | |
| 12 | Release the paper from on the platen. | Stop the suction fan operation. | |
