Telephone line based faxing

Error codeError descriptionCommunication typePhaseRemarks

Failure 201

Memory Full/Page Full (100 pages) occurs during accumulation of transmitted drafts.

TX

Insufficient memoryFailure 201

Memory Full/Page Full (100 pages) occurs during reception.

RXC
No toneFailure 203Busy tone detected when dialing.TXA
BusyFailure 204

Busy tone detected when dialing.

TXA
No responseFailure 205Fax signal from destination machine cannot be detected after dialing.TXA
Port inversionFailure 206Before calling (on hook) there was a line voltage but the line voltage was gone when calling (on hook).TXA
The line is not connected.Failure 207The line voltage is not detected before calling.TXA

Failure 208During sequential broadcast, transmission to some destination failed from among multiple destinations.TX

12Failure 202Received document length exceeds the set valueRXC
212Failure 202(Modem): Data sending end errorRX/TX

220Failure 202MCF was not sent after receiving dataRXD
400Failure 202T1 timer timed outTXBSending
401Failure 202Received a DCN after sending DCS.TXB
402Failure 202Received a DCN during sending the phase B.TXB
403Failure 202Receiver dose not have polling sending capability.RX(POL)B
404Failure 202No response after sending DCS.TXB
405Failure 202Fall back is not possible in sending.TXB
406Failure 202A DCN is sent after receiving DCS/DTC.RX/TX(POL)BSelect reception
407Failure 202No response or received a DCN after sending Post-command.TXD
408Failure 202Received a RTN.TXD
409Failure 202Received a PIN.TXD
410Failure 202Received a DCN during receiving phase D.RXD
411Failure 202Received a DCN after sending DTC.RX(POL)B
412Failure 202Cannot receive DSN after sending FTT.RXB
414Failure 202No response after DTC transmissionRX(POL)B
415Failure 202No document for polling sending.TX(POL)B
416Failure 202Cannot receive Post-commandRXD
417Failure 202Sent RTNRXD
420Failure 202T1 timer timed outRXBReceiving
422Failure 202Settings of DIS/DTC are disabled.TXB
427Failure 202Received a DCN after sending DISRXB
433Failure 202(Modem): Frame length errorRX/TXB,D
434Failure 202(Modem): Frame wait timeoutRX/TXB,D
436Failure 202Received a DCN after sending CFR/FTTRXC
438Failure 202A DCN is sent after receiving DCS/DTC.RX/TX(POL)B,DReception rejection
459Failure 202Training error occurred during receiving PIXRXC
490Failure 202Number of error line exceeds the limit value when receiving PIX.RXC
494Failure 202(Modem): Timeout between EOLRXC
495Failure 202Carrier disconnected during receive face CRXC
496Failure 202(Modem): Data transmission start errorTXB,C
501Failure 202(V.34) Modem mismatch errorV.34RX/TXB
502Failure 202(V.34) Primary channel end errorV.34RX/TXC
503Failure 202(V.34) Control channel start errorV.34RX/TXB,C,D
504Failure 202(V.34) Polling sending request is rejected in step V.8RX(POL)B
505Failure 202(V.34) Rejected the polling sending request in step V.8TX(POL)B
540Failure 202(ECM) No response or received a DCN after sending CTCTXD
541Failure 202(ECM) No response or received a DCN after sending EORTXD
542Failure 202(ECM) No response or received a DCN after sending RRTXD
543Failure 202(ECM) T5 timer timeoutTXD
544Failure 202(ECM) Sent DCN after sending EOR.TXD
550Failure 202(ECM) (modem): timeout between framesRXC
554Failure 202(ECM) ERR was sent after receiving EORRXD
580Failure 202The receiver dos not have F code (password) capability.TXB
582Failure 202The receiver (polling sending) dos not have F code (password) capability.RX(POL)B
826Failure 202SUB / SID or SEP / PWD did not matchRX/TX(POL)BReception rejection